Entra.News Dailydaily.entra.news
Aboutmerill.net
Microsoft Entra Global Secure Access

How to connect a remote network when your CPE is behind NAT - Microsoft Entra Global Secure Access

4 August 2026New+210 / −0 lines

In brief

Configure a Global Secure Access remote network when your customer premises equipment sits behind an upstream NAT router, using IKEv2 NAT Traversal (NAT-T).

Documentation change

new file mode 100644

title: How to connect a remote network when your CPE is behind NAT - Microsoft Entra Global Secure Access description: Configure a Global Secure Access remote network when your customer premises equipment sits behind an upstream NAT router, using IKEv2 NAT Traversal (NAT-T). ms.author: abhijeetsinha ms.reviewer: abhijeetsinha ms.service: global-secure-access ms.topic: how-to ms.date: 08/01/2026 ai-usage: ai-assisted

How to connect a Global Secure Access remote network when your CPE is behind a NAT device

Global Secure Access (GSA) remote networks connect a branch office or site to Microsoft's Security Service Edge over an IPsec tunnel between your customer premises equipment (CPE) - a router or firewall at the site - and the nearest GSA endpoint. GSA operates in responder mode, so the CPE always initiates the connection.

In the standard topology, the CPE has a public IP address on its WAN interface and dials out to GSA directly. This article covers a common, fully supported variation:

The CPE sits behind an upstream router that performs Network Address Translation (NAT). As a result, the CPE's WAN interface holds only a private IP address, and the public IP belongs to the upstream device.

The upstream device might be an ISP-provided modem/router, an SD-WAN edge, a carrier CPE, or another firewall. This works because of NAT Traversal (NAT-T), a standard part of IKEv2. This article explains the concept, shows how the connection is established, and describes how to configure the GSA remote network for this topology.

This article is a companion to How to create a remote network with Global Secure Access. Read that procedure first; this article only calls out what changes when a NAT device sits in front of the CPE.

Scenario overview

Element Value
CPE role IPsec initiator and BGP peer
GSA role IPsec responder and BGP peer
CPE WAN interface Private IP address
Upstream router Holds the public IP; performs source NAT/PAT; pure IP transit
Traffic path Branch LAN → CPE → upstream NAT router → internet → GSA endpoint
Enabling mechanism NAT Traversal (NAT-T), UDP 4500

The examples throughout this article use the following addresses. All are RFC 5737 (public examples), RFC 1918 (private), or RFC 6996 (private ASN) values.

flowchart LR
    LAN["Branch LAN<br/>10.1.0.0/16 · users"]
    CPE["CPE firewall<br/>LAN 10.1.0.1<br/>WAN 192.168.1.2 · private"]
    R["Upstream router<br/>LAN 192.168.1.1<br/>WAN 203.0.113.10 · public"]
    GSA["GSA endpoint<br/>198.51.100.20"]
    LAN -->|"branch · 10.1.0.0/16"| CPE
    CPE -->|"IKE / ESP · UDP 500 &rarr; 4500<br/>uplink · 192.168.1.0/24"| R
    R -->|"source NAT<br/>192.168.1.2 &rarr; 203.0.113.10"| GSA

There are three distinct segments here. The branch LAN (10.1.0.0/16) sits behind the CPE and is the network advertised to GSA over BGP. The uplink segment (192.168.1.0/24) is the private handoff between the CPE's WAN interface (192.168.1.2) and the upstream router. Beyond the router is the public side out to GSA.

The solid path is what the packets physically traverse; the upstream router rewrites the source address along the way. The IPsec tunnel and the BGP session terminate on the CPE and GSA only - the upstream router never participates in IPsec or BGP. It simply forwards, and NATs, the outer UDP packets.

Prerequisites

The CPE must meet the standard GSA remote network requirements: support for IPsec, IKEv2, GCMAES128/192/256 for phase 2, BGP, and route-based VPN with any-to-any (0.0.0.0/0) traffic selectors. Review Remote network valid configurations.

Additionally, for this topology:

  • The CPE must support and have NAT-T enabled (UDP 4500).
  • The upstream router must allow UDP 500 and 4500 outbound and the corresponding return traffic.
  • The upstream router's public IP should be static. A dynamic public IP breaks the tunnel whenever it changes and requires reconfiguration.

NAT Traversal (NAT-T) background

Why NAT breaks IPsec, and what NAT-T does

An IPsec tunnel uses two protocols on the wire:

  • IKE (Internet Key Exchange) runs over UDP port 500 and negotiates the security associations (keys, ciphers, lifetimes).
  • ESP (Encapsulating Security Payload) carries the encrypted traffic. ESP is IP protocol 50 - it is not a TCP or UDP protocol, so it has no port numbers.

A NAT device that performs Port Address Translation (PAT) - which is what most ISP routers do - tracks and de-multiplexes flows by port number. Because ESP has no ports, the NAT device has nothing to build a translation entry on, and the return packet can't be mapped back to the originating device. NAT also rewrites the source IP address, which breaks any peer identification or integrity check that depends on the original address.

NAT-T solves this in three parts:

  • NAT detection. During the initial IKE exchange (IKE_SA_INIT), both peers send NAT_DETECTION_SOURCE_IP and NAT_DETECTION_DESTINATION_IP payloads - hashes of the IP and port each peer believes it's using. If a NAT rewrote the address in transit, the received hash doesn't match, and the peer concludes a NAT is present.
  • Port float and UDP encapsulation. Once a NAT is detected, both sides move IKE from UDP 500 to UDP 4500, and ESP is wrapped in a UDP header - ESP-in-UDP, per RFC 3948 - also on UDP 4500. The encrypted payload now carries a port number, so the NAT device can build a normal translation entry and route return traffic correctly.
  • Keepalives. NAT-T keepalives (a small periodic packet on UDP 4500) keep the NAT translation entry alive so it doesn't age out during idle periods.

How the connection is established

When the CPE initiates, the upstream router applies source NAT, replacing the CPE's private WAN IP (192.168.1.2) with its own public IP (203.0.113.10). GSA detects the address mismatch, both peers float to UDP 4500 and encapsulate ESP in UDP, and authentication completes on the pre-shared key rather than the source IP. The route-based tunnel then comes up, and BGP peers over the tunnel on the inner addresses. The upstream router only ever forwards the outer UDP packets - it never sees the tunnel's plaintext, the IKE identity, or the BGP session.

sequenceDiagram
    participant C as "CPE 192.168.1.2"
    participant R as "Upstream router 203.0.113.10"
    participant G as "GSA 198.51.100.20"

    C->>R: IKE_SA_INIT (UDP 500)
    Note over R: Source NAT -> 203.0.113.10

    R->>G: IKE_SA_INIT from 203.0.113.10
    G-->>C: Response (NAT detected)

    Note over C,G: Switch to UDP 4500 (ESP-in-UDP)

    C->>G: IKE_AUTH (PSK, Child SA established)

    Note over C,G: Tunnel up - BGP 10.1.0.4 <-> 10.2.0.4 (TCP 179)

    loop Every 20 seconds
        C->>R: NAT-T Keepalive (UDP 4500)
    end

Device roles

The key architectural point: the CPE performs both IPsec and BGP; the upstream router performs neither.

Device IPsec role BGP role Function
CPE (firewall/router) Initiator; terminates the IKEv2 route-based tunnel BGP speaker; advertises on-premises prefixes, learns GSA routes Encrypts, decrypts, runs the tunnel and dynamic routing
Upstream router None None Source NAT/PAT and IP forwarding of UDP 500/4500. Pure transit - never sees plaintext, never joins the SA or BGP session
GSA endpoint Responder BGP peer (Microsoft ASN) Terminates Microsoft's side; applies traffic-forwarding policy

Set up the remote network for this scenario

The procedure follows the same steps as the base article. Only the highlighted items differ when the CPE is behind NAT.

Step 1: Basics

Enter the Name and Region of the remote network in the Microsoft Entra admin center. No change for this scenario.

Step 2: Connectivity - the key difference

When you add the device link, GSA identifies the incoming tunnel by the public source IP it observes and requires that the public IP you configure matches what arrives.

Enter these values in the device link:

Microsoft Entra admin center field Example value Meaning
Device IP address 203.0.113.10 The CPE's public IP as GSA observes it - the upstream router's public IP in this scenario
Device BGP address 10.1.0.4 The CPE's own BGP address
Device ASN 65001 The CPE's ASN
Local BGP address 10.2.0.4 GSA's own BGP address; entered as the peer BGP address on the CPE

The local and peer BGP addresses are reversed between the two sides:

  • Branch LAN: 10.1.0.0/16.
  • CPE: Local BGP address = 10.1.0.4, peer BGP address = 10.2.0.4.
  • GSA (Microsoft Entra): Device BGP address (also called peer) = 10.1.0.4, Local BGP address = 10.2.0.4.

Step 3: Traffic forwarding profile

Associate a traffic forwarding profile with the remote network. To avoid silently dropping traffic at the GSA gateway, associate both the Microsoft traffic profile and the Internet Access traffic profile where your licensing permits. No change for this scenario.

Step 4: View CPE connectivity configuration

Retrieve Microsoft's side of the connection from View configuration: Microsoft's public IP endpoint (198.51.100.20 in this example), its BGP address (10.2.0.4), and its ASN. Enter these on the CPE.

Step 5: Set up the CPE

Configure the CPE in its own management console using Microsoft's values from Step 4. In addition to the standard tunnel and BGP settings, apply the NAT-specific items in the checklist below.

Configuration checklist

Area Setting
Public IP in GSA The upstream router's public IP (203.0.113.10). Never the CPE's private WAN IP.
NAT-T on the CPE Enabled (auto-detect). If detection is unreliable through the upstream device, force NAT-T. UDP 4500 must be permitted end to end.
Keepalives and DPD Enable NAT-T keepalives and Dead Peer Detection so the upstream router's translation entry stays open (GSA can't reinitiate inbound).
Authentication The pre-shared key must match GSA exactly. Identify the peer by key/IKE identity, not by IP.
Crypto policy Phase 1 and phase 2 algorithms must match the GSA device link (default or custom IKE policy), using GCMAES.
VPN type Route-based (virtual tunnel interface) with any-to-any (0.0.0.0/0) traffic selectors.
BGP ASNs must differ. Local/peer addresses are reversed versus GSA. Add a static route to GSA's BGP address (10.2.0.4) over the tunnel interface so the CPE learns advertised routes.
Firewall rules Allow UDP 500 and 4500 and TCP 179 for the tunnel and BGP.
Upstream router Allow UDP 500/4500; disable any IPsec/VPN-passthrough ALG; use a generous UDP session timeout.
MTU / MSS Clamp TCP MSS on the tunnel interface to avoid fragmentation.

Verify and troubleshoot

Phase 1 (IKE) fails or GSA never responds.

  • Confirm the public IP in the GSA device link matches the upstream router's public IP.
  • Confirm the upstream router isn't remapping UDP 500 in a way that breaks detection, and that no IPsec/VPN-passthrough ALG is interfering. If the upstream device mangles the IKE port, port-forwarding UDP 500/4500 through to the CPE resolves it.
  • Confirm the pre-shared key and crypto policy match on both ends.

The tunnel drops when idle.

  • Enable NAT-T keepalives and DPD on the CPE.
  • Increase the UDP session timeout on the upstream router so the NAT mapping doesn't age out.

The tunnel is up but BGP won't establish.

  • Verify the static route to GSA's BGP address (10.2.0.4) points over the tunnel interface.
  • Verify the two ASNs are different and the local/peer BGP addresses are correctly reversed between the CPE and GSA.

Large packets or some flows fail intermittently.

  • Clamp TCP MSS and/or lower the tunnel MTU to account for ESP and NAT-T overhead.

The public IP changes.

  • A changing public IP on the upstream router invalidates the device link. Use a static public IP, or delete and recreate the link with the new address.

Related content